Max. power : Less than 1000 WCertification : ceVoltage : 210-240VPlug standard : ChineseFunction : Hot/cold airIs Smart Device : YESNumber of gears : 2Type of motor : ACPower Source : ElectricProduct Material : PP+ABSpet items : blow dryerdog accessories : dog hair dryerspet dryer : hair dryerDescription:Capacity 60L can hold about 1 cat under 9kgProduct size (mm) 502*442*467 L*W*HUse of equipment Top entry type puts in and takes out pets, and the large platform at the top can be used as an activity area for catsChanging pad (mm) 396*393*1.5 L*W*HUrinary tray (mm) 402*399*64 L*W*HPower switch button1. Click Turn on, the device turns on2. Click Close to shut down the device3. Click power during operation to enter standby mode, and shut down after 1 minute without operationDrying physical button There are 2 drying modes. The user clicks the "Drying" button on the device side, the default is to enter "Short Hair Drying", click to switch to "Long Hair Drying", then click to switch to "Short Hair Drying", and so on. Drying for long hair is 90 minutes (tentative), and drying for short hair is 60 minutes (tentative). The default drying time depends on the test results.The drying temperature depends on the test resultsLighting lamp When drying begins, the lighting lamp is turned on immediately, and when the drying is over, the lighting lamp is turned off immediatelyPTC heater1. After starting to dry for 5 seconds, the PTC heater is turned on and slowly heats up, and then the temperature in the box must be kept at 38.5°C. The fan will start running 15 seconds after the PTC is turned on.2. 2 minutes before the end of the operation, the PTC stops heating, and the negative ions are released for 2 minutes after the mode is turned on, and then released once every 10 minutes, once for 2 minutes.Buzzer1. There is a short tone when you click the button2. When the drying is over, the buzzer will emit 10 consecutive "dididi" to notify the user of the end of the drying.Fan1. After the drying starts, the fan will start running 15s after the PTC is turned on, and the wind speed will gradually increase to 2 gears within 10 seconds.2. 1 minute before the end of the drying countdown, the fan stops runningOzone physical button1. Long press for 5 seconds to turn on the ozone mode, click the power button to exit2. Before the ozone operation, make sure that there are no living things in the cabin3. The longest time of ozone operation is 20min4. When the ozone is running, the operating wind speed and drying are invalidNote: Hygienic standard for ozone in indoor air GB/T 18202-2000. This standard is expressed in terms of time concentration. The average maximum allowable concentration in 1 hour is 0.1mg/m³. The default disinfection time depends on the test results.Wind speed physical button1. There are 3 levels of wind speed, after turning on the drying, it will gradually increase to level 2 within 10 seconds and remain unchanged3. The default is 2 gears, click to adjust the wind speed gears, rotate to the right to increase by 1 gear, and to the left to decrease by 1 gear, every time there is a sense of pause.Time knob first click to unlock, and then set the time1. Rotate the time knob to the left, and perform subtraction based on the current time (multiple of 5)2. Rotate the time knob to the right, and add on the basis of the current time (multiple of 5)Care solutionThe care solution will be sprayed once 5 minutes after the beginning of the drying and 10 minutes before the end, 2 times in total, 15s each time. The time is to be determined for 15s. Follow-up adjustments will be made according to the test.Fault conditionsThere are 3 failures.1. E1: FTP over temperature2. E2: FTP does not heat up3. E3: Temperature probe failureButton tonePet requirementsSuitable for cats and small dogs, of which cats support under 9kg, and dogs support under 9kg.The care solution will be sprayed once 5 minutes after the beginning of drying and 10 minutes before the end, 2 times in total, each 15s can be used according to the test results; the release time depends on the test resultsDescription of oxygen content in the machine Oxygen concentration 21%High temperature alarm is an absolute safety measure, high temperature alarm 43 degreesElectrical specifications Rated voltage 220V 50HZPower interface non-pluggablePower cord 220V, 16AAmbient temperature and humidity -10 degrees Celsius ~ 40 degrees Celsius, 20%-100% humidityRated input power of main motor 25WMaximum power of the whole machine 890WNoise <50dBAKey material specifications Body material ABS+PCSurface treatment: (skin texture)Front transparent observation area PCTop transparent door PCQuality standard Executive standard GB17625.1-2012; GB4343.1-2018; GB4706.1-2005; GB4706.15-2008Product warranty for one yearFan life (hours) 15000High and low temperature test +55℃, 8h (power-on state) ~ -25℃, 8h (power-on state)Constant humidity test +25℃, RH: 45%, 48h (power-on state) including package testVibration test 2～8Hz, 7.5mm8～200Hz, 20m/s2, 5 sweep cycles in each axis2～10Hz,30m2/s310～200Hz, 3m2/s3 for 30 minutes in each direction, including package testUnsteady vibration (impact test) 300m/s2, 3 axis, 3 times each, including packaged machine testFree drop test 1.0M, 1 time on each of 6 sides, including packaging machine testAntistatic test 8KV(contact)\15KV(air)Protection grade IP3Packing specification Net weight (Kg) 7.1Gross weight (Kg) 8.5Carton size of single unit 626*566*590 L*W*Hpacking listHost 1Power cord 1Product manual 1Shell sparse one
English
Hindi
Indonesia
Deutsch
French
Vietnamese
Arabic
Korean
Espanol
Russian
Português
Turkish
HongKong
